Traditionally conceived to mimic a classic appearance (as found on vintage violins) Sunburst is truly a time honored guitar finish typically noticed on guitars aged and cutting edge. It's a greatly sought after look too tough to master for the average person?
It's possible to achieve a sunburst finish for your guitar if you comply with just a few steps and take great care. It's prudent to experiment initially by using a discarded bit of timber prior to trying your hand on the electric guitar.
If it's a new guitar kit,you really should put together your guitar first. Keep in mind you're going to be deconstructing to commence the finish but you have to know that you will not befinding problems further along that endanger the finish that you've simply put a great deal of valuable time towards.
After you have assembled the electric guitar and tested for potential issues you can start to prep the timber. Sand back until finally you've got a very smooth surface to work with. Then you should remove surplus dust particles and tidy the guitar meticulously.
Next apply some timber grain filler. You'll want to coat evenly over the top of the guitar and then really work it in. As soon as it has dried remove the excess and wipe off with a damp scrap of cotton material. Now it is the time to paint the back and sides of the body and neck of the electric guitar. A significant aspect to remember should be to mask the face and neck area.
As you are spraying paint or lacquer it's wise to keeping your aerosols in quite warm water before using. It's going to take a combination of coats for this reason you shouldn't try to apply too much all at one time. The trick will be to build up the tone layer after layer and apply from a fair distance away so that you can accomplish a gentle edge. The closer you get the more complicated the edge line you will end up with.
Next apply the amber lacquer. Chances are you'll be obliged to cover the sides that belong to the guitar and then place the guitar on the strong work bench face up before you apply. Once you have finished this step you can apply the clear coat next and sand between coats to get rid of any runs. Then apply the next darkest stain to achieve a blend of colouring within the edge and inner colours. Consider applying very thin and build up the obligatory coats. About now it's best to let the most recent coat harden off. When the guitar is completely free of moisture begin the process of sanding for a second time.
This really is a final detail. The key here is to use a lighter measure of sand paper every single time you end up being basically taking out the marks from the gauge of sandpaper applied preceding and then progressing which has a finer gauge. Keep delicately sanding and then changing to a finer gauge unless you run out of sandpaper after which you can move on to your buffer.From this point you may just continue to keep buffing or hand polishing until you end up getting completely happy with the finished look.
It's possible to achieve a sunburst finish for your guitar if you comply with just a few steps and take great care. It's prudent to experiment initially by using a discarded bit of timber prior to trying your hand on the electric guitar.
If it's a new guitar kit,you really should put together your guitar first. Keep in mind you're going to be deconstructing to commence the finish but you have to know that you will not befinding problems further along that endanger the finish that you've simply put a great deal of valuable time towards.
After you have assembled the electric guitar and tested for potential issues you can start to prep the timber. Sand back until finally you've got a very smooth surface to work with. Then you should remove surplus dust particles and tidy the guitar meticulously.
Next apply some timber grain filler. You'll want to coat evenly over the top of the guitar and then really work it in. As soon as it has dried remove the excess and wipe off with a damp scrap of cotton material. Now it is the time to paint the back and sides of the body and neck of the electric guitar. A significant aspect to remember should be to mask the face and neck area.
As you are spraying paint or lacquer it's wise to keeping your aerosols in quite warm water before using. It's going to take a combination of coats for this reason you shouldn't try to apply too much all at one time. The trick will be to build up the tone layer after layer and apply from a fair distance away so that you can accomplish a gentle edge. The closer you get the more complicated the edge line you will end up with.
Next apply the amber lacquer. Chances are you'll be obliged to cover the sides that belong to the guitar and then place the guitar on the strong work bench face up before you apply. Once you have finished this step you can apply the clear coat next and sand between coats to get rid of any runs. Then apply the next darkest stain to achieve a blend of colouring within the edge and inner colours. Consider applying very thin and build up the obligatory coats. About now it's best to let the most recent coat harden off. When the guitar is completely free of moisture begin the process of sanding for a second time.
This really is a final detail. The key here is to use a lighter measure of sand paper every single time you end up being basically taking out the marks from the gauge of sandpaper applied preceding and then progressing which has a finer gauge. Keep delicately sanding and then changing to a finer gauge unless you run out of sandpaper after which you can move on to your buffer.From this point you may just continue to keep buffing or hand polishing until you end up getting completely happy with the finished look.
About the Author:
Guitar Kits offer the beginner a great introduction to making guitars. For all the information you could ever require about Guitar Kits, check us out at www.eguitarkits.com
0 komentar:
Posting Komentar